Chapters
- Contents1
- Description and Specifications3
- Chapter 1 - Engine8
- Chapter 2 - Transmission61
- Chapter 3 - Power Take-Off71
- Chapter 4 - Belt Pulley75
- Chapter 5 - Rear Axle79
- Chapter 6 - Hydraulic System89
- Chapter 7 - Steering Gear101
- Chapter 8 - Service Bulletins111
- Engine: new valves and adjustable tappets112
- Engine overhaul gasket kit 8N-6008112
- Replacing crankshaft bearing liners113
- Intake valve seat insert change114
- Wrenches for adjustable tappets115
- Head bolt torque specifications115
- 8N engine overhaul115
- Servicing cast iron sleeves 8N-6055-B116
- Engine valve clearance116
- Oversize pistons and ring sets116
- Ignition: installing and timing the angle drive distributor117
- Distributor shaft 8N-12175117
- Corrections to the operator's manuals118
- Dust shield kit for the angle drive distributor118
- Transmission jumping out of reverse119
- Hydraulic pump exhaust valve retaining pins119
- 74034-S pin in the hydraulic lift cover120
- Servicing the 8N-640-A2 hydraulic pump exhaust valve121
- Rear axle spline and hub121
- Front wheel toe-in locating marks122
- Generator 8N-10000-B on 2N and 9N tractors122
- Carburetors on 8N tractors123
- 8N tractor changes 1 to 11123
- Bulletin Attachments126
Chapter 8 - Service Bulletins
8N tractor changes 1 to 11 page 125
Change No. 7 on All Tractors Starting with Serial No. 2l5043 on August 25a1949Old No. 350920-S Bolt (oil seal to retainer & cup assembly to center housing)New number remains the same. The revisions were made in the type of steel and thebolt is now full bodied instead of being necked down between the threads and theknurled portion. The increase in body size will tend to prevent chucking of thehub. The change in the steel will prevent the bolts from stretching.Change No. 8 on All Tractors Starting with Serial No. 216989 on September 2, 1949Old No. 8N-3512 Panel Assembly (instrument) replaced byNew No. 8N-3512-C Panel Assembly (instrument)The new panel has notches cut out at the bottom for the sector arms of thenew steering assembly.Change No. 9 on All Tractors Starting with Serial No. 216989 on September 2, 1949Old No. 8N-3503 Gear Assembly (steering) replaced byNew No. 8N-3503-B Gear Assembly (steering)In the old assembly the left hand sector was controlled from the ball nut and theright hand sector was controlled from the left sector, and both sectors weresupported by a bearing on one end only. In the new assembly the sectors havebearings for support at both ends. Another advantage is that now the right handsector is meshed directly with the ball nut and the left sector is meshed withthe right sector. Backlash in the assembly can be eliminated by tightening upthe adjusting screws extending through the right end left sides of the housing.In the event that a new steering assembly is to be installed on an older modeltractor, notches may be cut in the old panel assembly rather than replacing itwith the new panel assembly.Change No. 10 on All Tractors Starting with Serial No. 216989 on September 2, 1949Old No. 8N-3304 Link Assembly (steering drag) R.H. replaced byNew No. 8N-3305-B Link Assembly (steering drag) L.H.The above numbers are interchangeable.Old No. 8N-3305 Link Assembly (steering drag) L.H. replaced byNew No. 8N-3304-B Link Assembly (steering drag) R.H.The above numbers are interchangeable.See the chart on Page 22 of the Ford Tractor Parts and Accessories Catalog,PA 5933-2, for further information on drag links.On the old steering assembly the right hand drag link was the longest. In the newassembly the right sector is controlled directly by the ball nut and consequentlythe left hand drag link is the longest. There is no change in material or speci-fications only that the long drag link is now on the left side, and the short draglink is on the right side.Change No. 11 on All Tractors Starting with Serial Mo. 215050 on August 25, 1949Old No. 8N-7029 Washer (reverse idler gear thrust)New part number remains the same. The change involves the addition of two tabswhich are punched in the washer to anchor it to recesses in the transmission case.This prevents the washer from turning and wearing against the transmission case.125Free to read online. Contents · Where is the serial number on a 9N, 2N or 8N?
