Chapters
- Contents1
- Description and Specifications3
- Chapter 1 - Engine8
- Chapter 2 - Transmission61
- Chapter 3 - Power Take-Off71
- Chapter 4 - Belt Pulley75
- Chapter 5 - Rear Axle79
- Chapter 6 - Hydraulic System89
- Chapter 7 - Steering Gear101
- Chapter 8 - Service Bulletins111
- Engine: new valves and adjustable tappets112
- Engine overhaul gasket kit 8N-6008112
- Replacing crankshaft bearing liners113
- Intake valve seat insert change114
- Wrenches for adjustable tappets115
- Head bolt torque specifications115
- 8N engine overhaul115
- Servicing cast iron sleeves 8N-6055-B116
- Engine valve clearance116
- Oversize pistons and ring sets116
- Ignition: installing and timing the angle drive distributor117
- Distributor shaft 8N-12175117
- Corrections to the operator's manuals118
- Dust shield kit for the angle drive distributor118
- Transmission jumping out of reverse119
- Hydraulic pump exhaust valve retaining pins119
- 74034-S pin in the hydraulic lift cover120
- Servicing the 8N-640-A2 hydraulic pump exhaust valve121
- Rear axle spline and hub121
- Front wheel toe-in locating marks122
- Generator 8N-10000-B on 2N and 9N tractors122
- Carburetors on 8N tractors123
- 8N tractor changes 1 to 11123
- Bulletin Attachments126
Chapter 8 - Service Bulletins
74034-S pin in the hydraulic lift cover page 120
Retaining Pin No. 8N 641-B replaced Retaining Pin 8N 641-A beginningwith Tractor Serial No. 8N 56752 and continuing,3. THEORY OF NEW PART:Effective with Tractor Serial No. 8N 56752 the design of the ExhaustValve No. 8N 630 was changed as follows: The holes in the end of thevalve were eliminated because they were found to be a contributingfactor to the problem of sticky valves. This change necessitatedchanging the Retaining Pin No. 8N 641-A.4.. FIELD CORRECTION:When servicing the hydraulic pump on tractors below Serial No. 56752that are equipped with the old style Exhaust Valve No. 8N 630, useRetaining Pin No. 8N 641-A. When servicing tractors over Serial No.56752 with the new style Exhaust Valve No. 8N 640, use Retaining PinNo. 8N 641-B.Bulletin Subject: Failure of the 74034-S Pin in the Hydraulic Lift CoverAssembly (8N Tractor)1. PROBLEM:To prevent breakage of the subject pin in new tractors.2. PRODUCTION CORRECTION:Effective with tractor serial number 179,000, new fixtures for thepositive location of this pin hole were incorporated in production,3. FIELD CORRECTION:When the 74034-S pin breaks it is possible for pieces of the pin andthe 9N-526 rod to drop into the differential or the hydraulic pump. Theresulting damage is not only costly but the repair work involved is verytime consuming and might leave the farmer without his tractor at a verycritical time.To prevent this damage in the field, we strongly recommend that allundelivered tractors below serial number 179,000, in distributors anddealers stocks, be check to determine whether or not the 74034-S pinwill break. The procedure for this is to attach an implement to thetractor in the normal manner. Raise the implement just enough to barelyclear the ground, so that the implement is fully supported by the tractor.Next, remove the cover assembly from the right hand side of the tractorand reach in with your hand and feel the pin to determine whether it isloose or tight. If tight, it will indicate that the pin is taking thethrust and that a new 9N-526 should be installed. Be sure to check thenew 9N-526 and pin before replacing the lift cover on the tractor, to in-sure that there is no bind on the pin.120Free to read online. Contents · Where is the serial number on a 9N, 2N or 8N?
