Chapters
- Contents1
- Description and Specifications3
- Chapter 1 - Engine8
- Chapter 2 - Transmission61
- Chapter 3 - Power Take-Off71
- Chapter 4 - Belt Pulley75
- Chapter 5 - Rear Axle79
- Chapter 6 - Hydraulic System89
- Chapter 7 - Steering Gear101
- Chapter 8 - Service Bulletins111
- Engine: new valves and adjustable tappets112
- Engine overhaul gasket kit 8N-6008112
- Replacing crankshaft bearing liners113
- Intake valve seat insert change114
- Wrenches for adjustable tappets115
- Head bolt torque specifications115
- 8N engine overhaul115
- Servicing cast iron sleeves 8N-6055-B116
- Engine valve clearance116
- Oversize pistons and ring sets116
- Ignition: installing and timing the angle drive distributor117
- Distributor shaft 8N-12175117
- Corrections to the operator's manuals118
- Dust shield kit for the angle drive distributor118
- Transmission jumping out of reverse119
- Hydraulic pump exhaust valve retaining pins119
- 74034-S pin in the hydraulic lift cover120
- Servicing the 8N-640-A2 hydraulic pump exhaust valve121
- Rear axle spline and hub121
- Front wheel toe-in locating marks122
- Generator 8N-10000-B on 2N and 9N tractors122
- Carburetors on 8N tractors123
- 8N tractor changes 1 to 11123
- Bulletin Attachments126
Chapter 8 - Service Bulletins
Engine overhaul gasket kit 8N-6008 page 112
8N TRACTOR SERVICE INFORMATIONENGINEBulletin Subject: New Valves and Adjustable Tappets for theFord Tractor Kit, No. 8N-6546Over the past year, in certain localities, a few owners have encountered somedifficulty with tractor engine valves sticking or burning, particularly theexhaust valve. For the purpose of relieving this condition, new valves andadjustable tappets have been developed for service replacement on the FordTractor.The new valve will relieve exhaust valve failure attributable to excessivedeposits of the valve seat and/or valve stem. These experiences are localin character, and replacement of the standard valves with the new valves isnot subject to warranty or policy adjustment. Please do not submit S.A.R.'sfor replacements.A kit, Part No. 8N-6546, is now being made available. It contains four newvalve assemblies and eight adjustable tappets with wrenches. The wrenches areincluded to hold the tappets while adjustments are being made for length.In Attachment No. 1 you will find a complete description of the valve as wellas a drawing and instructions for proper installation and servicing. Completeinstructions for the installation of the tappets are included in each kit. Youwill note that tappets are to be used for all eight valves however, the newvalves should be used only in the exhaust ports.These kits are available for immediate shipment as announced in "Service PartsRelease and Change Notice No. 5O-2". Dealers should be advised of the avail-ability of the subject parts, particularly in those areas where sticking orburning valves are now a problem.Bulletin Subject: Engine Overhaul Gasket Kit, Part No. 8N-6008Service Parts Release and Change Notice, 50-4, dated April 1, 1950, page 15,lists "Part No. 9N-6008 Motor Overhaul Gasket Kit REPLACED BY Part No. 8N-6008Motor Overhaul Gasket Kit."Part No. 9N-6008 kit, now in Distributor and Dealer inventory, should be usedfor the servicing of all tractors prior to the installation of the angle drivedistributor only.In addition to the gaskets, there are three 6020 series Front Cover Gasketsincluded in the new 8N-6008 Engine Overhaul Gasket Kit, so that the kit will beuniversally applicable to all 8N and 9N tractors. The three 6020 series gasketsall appear to be exactly alike, but actually there is a slight difference in eachone.112Free to read online. Contents · Where is the serial number on a 9N, 2N or 8N?
