Chapters
- Contents1
- Description and Specifications3
- Chapter 1 - Engine8
- Chapter 2 - Transmission61
- Chapter 3 - Power Take-Off71
- Chapter 4 - Belt Pulley75
- Chapter 5 - Rear Axle79
- Chapter 6 - Hydraulic System89
- Chapter 7 - Steering Gear101
- Chapter 8 - Service Bulletins111
- Engine: new valves and adjustable tappets112
- Engine overhaul gasket kit 8N-6008112
- Replacing crankshaft bearing liners113
- Intake valve seat insert change114
- Wrenches for adjustable tappets115
- Head bolt torque specifications115
- 8N engine overhaul115
- Servicing cast iron sleeves 8N-6055-B116
- Engine valve clearance116
- Oversize pistons and ring sets116
- Ignition: installing and timing the angle drive distributor117
- Distributor shaft 8N-12175117
- Corrections to the operator's manuals118
- Dust shield kit for the angle drive distributor118
- Transmission jumping out of reverse119
- Hydraulic pump exhaust valve retaining pins119
- 74034-S pin in the hydraulic lift cover120
- Servicing the 8N-640-A2 hydraulic pump exhaust valve121
- Rear axle spline and hub121
- Front wheel toe-in locating marks122
- Generator 8N-10000-B on 2N and 9N tractors122
- Carburetors on 8N tractors123
- 8N tractor changes 1 to 11123
- Bulletin Attachments126
Chapter 8 - Service Bulletins
8N engine overhaul page 115
Bulletin Subject: Wrenches for Adjustable TappetsThe recently announced tappet wrenches, Part No. 8N-17045-A Right Hand andPart No. 8N-17046-A Left Hand are designed to prevent tappets from turningwhile making the necessary tappet adjustments.See Attachment #2 for instructions.The price structure for the subject wrenches has been released in ServiceParts Release and Change Notice 5l-5 dated May 1, 1951 and is currentlyin your hands.Bulletin Subject: Ford Tractor Head Bolt Torque SpecificationsThe use of the recommended head bolt torque is essential in the proper in-stallation of the cylinder head. Improperly tightened head bolts could resultin damage to the engine such as, warpage of the cylinder head, water leakageand cylinder head gasket failure. The torque specifications and correct pro-cedure for tightening head bolts are covered in detail in Attachment #3.Bulletin Subject: 8N Ford Tractor EngineOverhauls on the 8N Ford Tractor engine must be done carefully and properly ifmaximum performance in engine life is to be expected and customers satisfied.In this connection the importance of properly fitting pistons, piston rings,piston pins, connecting rods and bearings cannot be over-emphasized.Complete instructions have been furnished to you for the dealers1ServiceDepartments in the Ford Tractor Repair Manual, Form No. 3695-47,and byvarious bulletins from the Dearborn Service Department. However, we find thatthese instructions are not being carried out in many service shops. It ispossible that the mechanics do not have the complete specifications readilyavailable to aid them in performing these important service operations moreaccurately and efficiently.To make these complete specifications available to all dealer service shopsimmediately, we have gathered it together in Attachment #4, which covers in detail:1. Proper piston fit to cylinder bore.2. Specifications for piston ring side clearance.3. Connecting rod alignment.4. Checking crankshaft bearing clearances.We are sure that you and your dealers will be happy to receive this informationand know that if the procedures are carried out in detail, satisfactory resultswill be obtained in the correction of excessive oil consumption and loss ofpower.115Free to read online. Contents · Where is the serial number on a 9N, 2N or 8N?
