Chapters
- Contents1
- Description and Specifications3
- Chapter 1 - Engine8
- Chapter 2 - Transmission61
- Chapter 3 - Power Take-Off71
- Chapter 4 - Belt Pulley75
- Chapter 5 - Rear Axle79
- Chapter 6 - Hydraulic System89
- Chapter 7 - Steering Gear101
- Chapter 8 - Service Bulletins111
- Engine: new valves and adjustable tappets112
- Engine overhaul gasket kit 8N-6008112
- Replacing crankshaft bearing liners113
- Intake valve seat insert change114
- Wrenches for adjustable tappets115
- Head bolt torque specifications115
- 8N engine overhaul115
- Servicing cast iron sleeves 8N-6055-B116
- Engine valve clearance116
- Oversize pistons and ring sets116
- Ignition: installing and timing the angle drive distributor117
- Distributor shaft 8N-12175117
- Corrections to the operator's manuals118
- Dust shield kit for the angle drive distributor118
- Transmission jumping out of reverse119
- Hydraulic pump exhaust valve retaining pins119
- 74034-S pin in the hydraulic lift cover120
- Servicing the 8N-640-A2 hydraulic pump exhaust valve121
- Rear axle spline and hub121
- Front wheel toe-in locating marks122
- Generator 8N-10000-B on 2N and 9N tractors122
- Carburetors on 8N tractors123
- 8N tractor changes 1 to 11123
- Bulletin Attachments126
Chapter 8 - Service Bulletins
Replacing crankshaft bearing liners page 113
Since there are no identifying markings on the parts, it is necessary toselect the proper gasket to fit the engine being overhauled. If there isany doubt, the gasket should be matched with the mating parts on which itwill be used.Information on the application of these three particular gaskets is listedbelow.9N-6020-B Gasket (Cylinder Front Cover)This part is for use with all engine assemblies prior to tractorSerial No. 263844.8N-6020-B Gasket(Cylinder Front Cover)This part is for use on engine assemblies equipped with the angledrive distributor that may have the cast iron front and the castiron timing gear side covers.8N-6020C Gasket (Cylinder Front Cover)This part is used on engine assemblies equipped with the angle drivedistributor using the aluminum front and aluminum timing gear side covers.Part No. 8N-6019A cover (cylinder front, cast iron) and Part No. 8N-6017Acover (cylinder timing gear side, cast iron) have not been used in production,but are listed as optional and may be used in the future. The Part No.8N-6020-B, Gasket Cylinder Front Cover, is supplied in the Engine OverhaulGasket Kit for use with the cast iron covers.Bulletin Subject: Factors to Consider in Replacing Crankshaft Bearing LinersIt is well recognized that crankshaft bearing liners perform a vital functionin the proper operation of the Ford tractor engine. Liners that are actuallyworn or damaged will cause excessive wear of related engine parts, & drop inengine oil pressure and increased engine noise. Therefore, the matter ofwhether crankshaft bearing liners SHOULD or SHOULD NOT be replaced merits care-ful consideration when the above engine conditions are noted or when an engineis torn down for general overhaul.The following factors should be considered in checking the condition of linersand used as a guide in determining whether liners should be replaced.1. Clearance between the liners and the crankshaft journals. This is themost important factor in checking bearings to determine whether theliners should be replaced. These clearances in the Ford Tractor engineshould be as follows:BEARING LINERSNEWWEAR LIMITMain.001 - .003.005Crank Pin .OOO4 - .0025.005End Play.002 - .006.008These clearances should be carefully checked before liners are replaced.The use of Plastigage, as made available to the field by the Parts113Free to read online. Contents · Where is the serial number on a 9N, 2N or 8N?
