Chapters
- Contents1
- Description and Specifications3
- Chapter 1 - Engine8
- Chapter 2 - Transmission61
- Chapter 3 - Power Take-Off71
- Chapter 4 - Belt Pulley75
- Chapter 5 - Rear Axle79
- Chapter 6 - Hydraulic System89
- Chapter 7 - Steering Gear101
- Chapter 8 - Service Bulletins111
- Engine: new valves and adjustable tappets112
- Engine overhaul gasket kit 8N-6008112
- Replacing crankshaft bearing liners113
- Intake valve seat insert change114
- Wrenches for adjustable tappets115
- Head bolt torque specifications115
- 8N engine overhaul115
- Servicing cast iron sleeves 8N-6055-B116
- Engine valve clearance116
- Oversize pistons and ring sets116
- Ignition: installing and timing the angle drive distributor117
- Distributor shaft 8N-12175117
- Corrections to the operator's manuals118
- Dust shield kit for the angle drive distributor118
- Transmission jumping out of reverse119
- Hydraulic pump exhaust valve retaining pins119
- 74034-S pin in the hydraulic lift cover120
- Servicing the 8N-640-A2 hydraulic pump exhaust valve121
- Rear axle spline and hub121
- Front wheel toe-in locating marks122
- Generator 8N-10000-B on 2N and 9N tractors122
- Carburetors on 8N tractors123
- 8N tractor changes 1 to 11123
- Bulletin Attachments126
Chapter 8 - Service Bulletins
8N tractor changes 1 to 11 page 124
Change No. 2 on All Tractors Starting with Serial No. 217307 on September 1, 1949Old No. 8N-698-B Valve (intake control hydraulic pump) replaced byNew No. 8N-698-B Valve (intake control hydraulic pump)The old valve had a short taper, while the new one has a much longer one. Thislonger tapered valvs meters the oil to the intake holes in the bushing.Change No. 3 on All Tractors Starting with Serial No. 215759 on August 29, 1949Old No. 8N-539 Spring (draft control) replaced byNew No. 8N-539-B Spring (draft control)This change has been made to provide a more positive fulcrum for the long controllever 8N-540, thus insuring a full intake position of the intake valve when coldoil would tend to resist this movement of the valve. The new springs are paintedred to enable them to be quickly distinguished from the old springs which werenot painted.In addition, the free length of the new spring is1/2" shorter than the old one.This new spring in no way changes previous instructions on adjusting the springsin the lift cover. A length of 3.58 inches or roughly 3-37/64 inches is stillcorrect.Change No. 4 on All Tractors Starting with Serial No. 215759 on August 29, 1949Old No. 8N-541 Plunger (hydraulic lift draft control spring) replaced byNew No. 8N-541-B Plunger (hydraulic lift draft control spring)Both of these plungers have the same over-all length, but the new one has alarger diameter head at the clevis end. This provides more bearing area on plateNo. 8N-527.Change No. 5 on All Tractors Starting with Serial No. 215759 On August 29, 1949Old No. NCA-527-A Plate Assembly (hand lift cover)Part number remains the same. The only revision made was in the steel and heattreatment thus increasing its strength.Change No. 6 on All Tractors Starting with Serial No. 215759 on August 29, 1949Old No. 8N-535 Rocker (hydraulic lift) replaced byNew No. NCA-535-A Rocker(hydraulic lift)The old rocker has a single hole for attaching the top link. The new rocker hasbeen built up with two additional holes for the top link attachment for occasionswhen the draft of the implement is so light that little or no reaction is re-gistered through the main control spring. In such cases it will be possible toraise the top link into one of the additional positions provided to increase itsleverage over the main control spring.A general rule that may be followed regarding the position of the top link in therocker is that the top hole is for light draft, middle hole for medium draft andbottom hole for heavy draft. If an implement with heavy draft is used with the toplink in the top hole it upsets the balance of the hydraulic control, which can becorrected by putting the top link in the bottom hole.124Free to read online. Contents · Where is the serial number on a 9N, 2N or 8N?
