Chapters
- Contents1
- Description and Specifications3
- Chapter 1 - Engine8
- Chapter 2 - Transmission61
- Chapter 3 - Power Take-Off71
- Chapter 4 - Belt Pulley75
- Chapter 5 - Rear Axle79
- Chapter 6 - Hydraulic System89
- Chapter 7 - Steering Gear101
- Chapter 8 - Service Bulletins111
- Engine: new valves and adjustable tappets112
- Engine overhaul gasket kit 8N-6008112
- Replacing crankshaft bearing liners113
- Intake valve seat insert change114
- Wrenches for adjustable tappets115
- Head bolt torque specifications115
- 8N engine overhaul115
- Servicing cast iron sleeves 8N-6055-B116
- Engine valve clearance116
- Oversize pistons and ring sets116
- Ignition: installing and timing the angle drive distributor117
- Distributor shaft 8N-12175117
- Corrections to the operator's manuals118
- Dust shield kit for the angle drive distributor118
- Transmission jumping out of reverse119
- Hydraulic pump exhaust valve retaining pins119
- 74034-S pin in the hydraulic lift cover120
- Servicing the 8N-640-A2 hydraulic pump exhaust valve121
- Rear axle spline and hub121
- Front wheel toe-in locating marks122
- Generator 8N-10000-B on 2N and 9N tractors122
- Carburetors on 8N tractors123
- 8N tractor changes 1 to 11123
- Bulletin Attachments126
Chapter 8 - Service Bulletins
Intake valve seat insert change page 114
Department in their Parts and Accessories Bulletin #81, will materiallyreduce the time and effort required to accurately check these clearances.Liners in which the clearance is not within the above wear limit shouldbe replaced.2. Presence of foreign material in the liner. Excessive amounts of foreignmaterial embedded in the face of the liner may eventually cause unnecessarywear in the journals, and therefore, justifies replacing the liners. How-ever, slight amounts of foreign material will do no harm and should not beconsidered as cause for liner replacement.3. Liner Fatigue. This condition is indicated by areas in the face of theliner deteriorating or crumbling away leaving a ragged opening or pit inthe face of the liner. Bearings otherwise satisfactory but with smallpits need not be replaced. Bearings must be replaced where pits extendto the side of the liner and permit oil to escape.4. Discoloration. Bearing liners may sometimes be discolored. This is notharmful and will not shorten the life of the bearing. Discoloration initself, is not justification for replacing the bearing liners.5. Unnecessary Replacement. It is important that the need for bearing linerreplacement be fully established before such action is taken. Our recordsindicate a tendency toward replacing liners unnecessarily. In view ofthe fact that replaced liners are subject to recall for inspection pendingapproval of claims, you are urged to make certain that, in accordance withthe above four factors, the liners are defective and actually need to bereplaced.Bulletin Subject: Tractor Changes-Use for Effective Point of Change OnlyEffective with Tractor Serial No. 318023, the intake valve seat insert, PartNo. 40-6057-B, has been removed from the Block Assembly, Part No. 8N-6010-B,and the Cylinder Assembly, Part No. 8N-6011-B. The seat is now integral withthe block.Extensive testing has proven that elimination of this intake valve seat insertwill in no way affect the normal life of the engine block.Occasionally you may find an intake valve seat insert used in a new tractorengine or service engine block, however, this will be an exception and shouldnot be cause for concern in the field.Valve seat insert, Part No. 40-6057-B, will continue to be sold as a serviceitem and can be used to recondition engine blocks in the field where it is foundto be necessary.Manufacturers of the various types of seat grinding equipment provide detailedinstructions for all steps in reconditioning valve seats, on both the cast andinsert type, and these instructions should be followed.114Free to read online. Contents · Where is the serial number on a 9N, 2N or 8N?
