Chapters
- Contents1
- Description and Specifications3
- Chapter 1 - Engine8
- Chapter 2 - Transmission61
- Chapter 3 - Power Take-Off71
- Chapter 4 - Belt Pulley75
- Chapter 5 - Rear Axle79
- Chapter 6 - Hydraulic System89
- Chapter 7 - Steering Gear101
- Chapter 8 - Service Bulletins111
- Engine: new valves and adjustable tappets112
- Engine overhaul gasket kit 8N-6008112
- Replacing crankshaft bearing liners113
- Intake valve seat insert change114
- Wrenches for adjustable tappets115
- Head bolt torque specifications115
- 8N engine overhaul115
- Servicing cast iron sleeves 8N-6055-B116
- Engine valve clearance116
- Oversize pistons and ring sets116
- Ignition: installing and timing the angle drive distributor117
- Distributor shaft 8N-12175117
- Corrections to the operator's manuals118
- Dust shield kit for the angle drive distributor118
- Transmission jumping out of reverse119
- Hydraulic pump exhaust valve retaining pins119
- 74034-S pin in the hydraulic lift cover120
- Servicing the 8N-640-A2 hydraulic pump exhaust valve121
- Rear axle spline and hub121
- Front wheel toe-in locating marks122
- Generator 8N-10000-B on 2N and 9N tractors122
- Carburetors on 8N tractors123
- 8N tractor changes 1 to 11123
- Bulletin Attachments126
Chapter 8 - Service Bulletins
Rear axle spline and hub page 121
Bulletin Subject: Servicing Part No. 8N-640-A2 Hydraulic Pump Exhaust ValveUp to the present time (October, 1949)}the subject valve has only been avail-able under one part number, 8N-640-A2. We are now making this valve in fivesizes for service stock, each carrying its own part number and color code.It is recommended that the exhaust valve always be fitted with a minimum ofclearance. Now, for the first time, the Ford tractor service representativehas a selection of valve sizes which enables him to make the best fit, under anycircumstance. It is very important that the exhaust valve be properly fittedin the bushing for best operation of the hydraulic mechanism. To determine thisfit, begin with the largest size valve and continue down the color code until themaximum valve size goes into the bushing. This should give a medium tight fit.This fit should be checked with the specified hydraulic oil on the valve andbushing. There is little danger of getting too tight a fit as long as the exhaustvalve moves uniformly throughout its travel.Should you find it necessary to replace the exhaust bushing (8N-625) because ofscore marks, be sure to install the new one with the holes in a vertical positionin the pump housing.The part number, size and corresponding color code of each valve is listed below:Part No.Size of ValveColor Code8N-640-A2.5917 - .5918White8N-640-B.5918 - .5920Blue8N-640-C.5920 - .5921Yellow8N-640-D.5923 -.5924Green8N-640-E.5925 - .5926OrangeAll of the valves listed above are available for immediate shipment and should beordered in the usual manner, by individual part numbers.REAR AXLE AND DRIVEBulletin Subject: Rear Axle Spline and Hub1. PROBLEM:To insure tight fit of hub and rear axle.In performing rear axle service operations that require the removal of a hub,we have found it advantageous to always replace the hub in the same positionon the rear axle spline. This practice helps assure a good fit by utilizingthe seat established in the original assembly of the tractor.2, PRODUCTION CHANGE:Effective with Tractor Serial Number 8N147254all rear axle splines and hubs121Free to read online. Contents · Where is the serial number on a 9N, 2N or 8N?
