Chapters
- Contents1
- Description and Specifications3
- Chapter 1 - Engine8
- Chapter 2 - Transmission61
- Chapter 3 - Power Take-Off71
- Chapter 4 - Belt Pulley75
- Chapter 5 - Rear Axle79
- Chapter 6 - Hydraulic System89
- Chapter 7 - Steering Gear101
- Chapter 8 - Service Bulletins111
- Engine: new valves and adjustable tappets112
- Engine overhaul gasket kit 8N-6008112
- Replacing crankshaft bearing liners113
- Intake valve seat insert change114
- Wrenches for adjustable tappets115
- Head bolt torque specifications115
- 8N engine overhaul115
- Servicing cast iron sleeves 8N-6055-B116
- Engine valve clearance116
- Oversize pistons and ring sets116
- Ignition: installing and timing the angle drive distributor117
- Distributor shaft 8N-12175117
- Corrections to the operator's manuals118
- Dust shield kit for the angle drive distributor118
- Transmission jumping out of reverse119
- Hydraulic pump exhaust valve retaining pins119
- 74034-S pin in the hydraulic lift cover120
- Servicing the 8N-640-A2 hydraulic pump exhaust valve121
- Rear axle spline and hub121
- Front wheel toe-in locating marks122
- Generator 8N-10000-B on 2N and 9N tractors122
- Carburetors on 8N tractors123
- 8N tractor changes 1 to 11123
- Bulletin Attachments126
Chapter 8 - Service Bulletins
Oversize pistons and ring sets page 116
Bulletin Subject: Servicing Cast Iron Sleeves, Part No. 8N-6055-BAs announced in Service Bulletin No. 190, dated December 5, 1951, cast ironsleeves were incorporated in production, effective with Tractor Serial No.8N-433578.Parts and Accessories Bulletin No. 202, dated January 2, 1952, announced theavailability of the subject sleeve as a service item. In Attachment #5,instructions outline the correct procedure for servicing these sleeves in thefield, and should be followed in detail to obtain satisfactory results.Bulletin Subject: Engine Valve ClearanceInsufficient clearance between the tappet and the valve stem is one of theprimary causes for valve burning. However, particles of carbon that lodgebetween the valve face and the valve seat are sometimes responsible for whatappears to be insufficient valve clearance. The carbon does not allow thevalves to completely close and in turn excessive heat is retained at thevalve face which cannot be dissipated without contacting the valve seat.When adjusting the valve tappets for proper clearances, as given in ServiceBulletin No. 179, a uniform method of procedure is of extreme importance.The proper cold clearance for setting exhaust valves is .014 to .016 end forintake valves, .0l0 to .012.In order to specify a uniform method of checking valve clearance on the tractor,the following chart is suggested:VALVES OPEN#1 Exhaust and 3 Intake#1 Intake and 2 Exhaust#2 Intake and 4 Exhaust#3 Exhaust and 4 IntakeVALVES TO BE CHECKED#2 Intake and 4 Exhaust#3 Exhaust and 4 Intake#1 Exhaust and 3 Intake#1 Intake and 2 ExhaustCorrect adjustment of valve clearance may be obtained only if the valves indicatedin the above chart are in full open position and with the engine at room tempera-ture (approximately 70° F.).When checking valve clearance, it cannot be overemphasized that the tappet shouldbe against the flat of the cam and not on the cam ramp. In some cases it hasbeen found that the tippet actually is not in contact with the cam when valveclearances ere set, thus causing excessive clearance.Bulletin Subject: Oversize Pistons and Ring SetsParts and Accessories Bulletin No. 267, dated December 1, 1952, announced theavailability of oversized pistons and ring sets. These parts may only be usedin 8N tractors which incorporate the cast iron sleeve, Part No. 8N-6055-B, asit is necessary to rebore and hone the sleeves to obtain the recommended pistonfit to cylinder bore of 5 - 10 pounds pull, using a .002 x .50 ribbon pull scale.116Free to read online. Contents · Where is the serial number on a 9N, 2N or 8N?
