Chapters
- Contents1
- Description and Specifications3
- Chapter 1 - Engine8
- Chapter 2 - Transmission61
- Chapter 3 - Power Take-Off71
- Chapter 4 - Belt Pulley75
- Chapter 5 - Rear Axle79
- Chapter 6 - Hydraulic System89
- Chapter 7 - Steering Gear101
- Chapter 8 - Service Bulletins111
- Engine: new valves and adjustable tappets112
- Engine overhaul gasket kit 8N-6008112
- Replacing crankshaft bearing liners113
- Intake valve seat insert change114
- Wrenches for adjustable tappets115
- Head bolt torque specifications115
- 8N engine overhaul115
- Servicing cast iron sleeves 8N-6055-B116
- Engine valve clearance116
- Oversize pistons and ring sets116
- Ignition: installing and timing the angle drive distributor117
- Distributor shaft 8N-12175117
- Corrections to the operator's manuals118
- Dust shield kit for the angle drive distributor118
- Transmission jumping out of reverse119
- Hydraulic pump exhaust valve retaining pins119
- 74034-S pin in the hydraulic lift cover120
- Servicing the 8N-640-A2 hydraulic pump exhaust valve121
- Rear axle spline and hub121
- Front wheel toe-in locating marks122
- Generator 8N-10000-B on 2N and 9N tractors122
- Carburetors on 8N tractors123
- 8N tractor changes 1 to 11123
- Bulletin Attachments126
Chapter 8 - Service Bulletins
Dust shield kit for the angle drive distributor page 118
3. Drill the first hole to hold the collar in this position and rivet itin place,4. Remove the shim or feeler.5. Place the gear, Part No. 7RA 12390-C, on the shaft and remove the clampand arm assembly, Part No. 7HA 12273, which is clamped against theshoulder on the distributor housing. Measure from this shoulder down4.020 inches on the shaft and locate the bottom edge of the gear at thispoint.6. This properly locates the gear and the hole may now be drilled in linewith the holes in the gear and the gear riveted in place. Reattach thearm assembly, Part No. 7HA 12273.Bulletin Subject: Correction of Errors in Tractor Operator's Manuals,Form No. 3729-50-F and 3729-50-MPlease make the following corrections on Page 10 under "Ignition System".These corrections apply only to tractors with the angle drive distributorinstallation.Under Distributor: The specifications on lines 4 and 8 now read:Initial timing (degrees of crankshaft) Top dead centerBreaker contact spacing0.015"Under Distributor: The specifications on lines 4 and 8 should read:Initial timing (degrees of crankshaft) 4 before top dead centerBreaker contact spacing.024"— .026"Dealers should make the above corrections in the Operator's Manual during hispre-delivery inspection of the Ford Tractor.The text for Ignition Timing on Pages 92, 93, 94 and 95 of the subject manualsis correct and need not be changed.Bulletin Subject: Dust Shield Kit, Part No. 8N-12261-A for Angle Drive DistributorThe subject Dust Shield Kit, designed to prevent dust from entering the distributorassembly, is now available for service.Investigation of premature point failures has revealed that abrasive dust and lackof cam lubrication are, in many cases, responsible for point failures. The pre-sence of dust and the absence of lubrication causes rapid wear of the fiber blockand if permitted to continue, the cam, of the cam and weights assembly, Part No.8N-12176, will become scored. A scored distributor cam will cause rapid wear ofthe fiber block. This in turn will result in improper point spacing, arcing be-tween the contacts, and rapid pitting of the points.118Free to read online. Contents · Where is the serial number on a 9N, 2N or 8N?
