Free shipping to US addressesShips the next business day Call 260-496-8606
NewOldManuals.com Service, parts & operator's manuals for tractors and construction equipment
Cart (0)
Storewide sale — 20% off every manual · plus free USA shipping
Chapters

All chapters and sections

  1. Contents1
  2. Description and Specifications3
  3. Chapter 1 - Engine8
  4. Chapter 2 - Transmission61
  5. Chapter 3 - Power Take-Off71
  6. Chapter 4 - Belt Pulley75
  7. Chapter 5 - Rear Axle79
  8. Chapter 6 - Hydraulic System89
  9. Chapter 7 - Steering Gear101
  10. Chapter 8 - Service Bulletins111
  11. Bulletin Attachments126

Bulletin Attachments

#5 Servicing cast iron sleeves page 134

Ford 8N, 9N, 2N Service Manual, page 134ATTACHMENT #5INSTRUCTIONSFORSERVICING CAST IRON SLEEVESPART NO. 8N-6055-B1. Remove the old sleeves from the cy-linder block as follows:a. Remove the manifold and all valveassemblies.b. Remove cylinder ridge.c. Remove the connecting rod and pis-ton assemblies.d. Remove the old sleeves with a con-stant pressure type sleeve remover.e. Cover the crankshaft with an oilsoaked cloth.f. Clean all varnish and carbon fromthe cylinder block bore with a de-glazing tool.g. Scrape the counter bore clean witha suitable tool.NOTE: In all cases valve faces and seatsshould be reconditioned after installingsleeves. This is necessary to correctfor any valve seat distortion that maybe caused by the press fit of the sleevesinto the cylinder block bores.2. Install the new cast iron sleeves asfollows:a. Wash each sleeve in gasoline ornaptha to remove the protectivecoating of oil and dry the sleevethroughly.CAUTION: Do not use an impact typesleeve installer.b. Press the sleeves into the cylinderblock bores with a screw or con-stant pressure type sleeve install-er.NOTE: When reconditioning valve seatsthey should be checked with a dial in-dicator for runout. If this runout isfound to be in excess of .0015, the val-ve seats should be ground and checkedagain.3. Fit each piston to its respectivesleeve bore using a pull scale witha .002 x1/2" feeler gauge as speci-fied in Service Bulletin No. 182,dated October 5, 1951. In the major-ity of cases, to obtain the requiredfit of 5-10 pounds pull, it will benecessary to hone the sleeve bore.If honing is necessary a suggestedprocedure is provided below.a. Use a rigid type hone and No. 220grit stones. A drill with a capa-city of 250-450 RPM should be usedto drive the hone.NOTE: The speed of the hone and rapid-ity of the stroke governs the crosshatch marks on the sleeve. The crosshatch marks should intersect at approx-imately 90° for proper ring seating.b. Operate the hone through the bore10 or 12 complete strokes. Removethe hone, clean the sleeve withdry rags, and recheck the pistonfit.c. Repeat the above procedure, untilthe necessary amount of materialhas been removed for the speci-fied piston to bore fit.CAUTION: Do not use gasoline or kero-sene to clean the sleeve walls afterthe honing operation. Solvents of thistype will not remove the abrasive butwill further embed small abrasive par-ticles into the pores of the cylinderblock. Diagram "A" shows the surfaceof a sleeve wall before it has beenproperly cleaned and after it has beencleaned by following recommendedprocedure.4. Clean the cylinder block of all for-eign material as follows:a. Wipe or remove as much of the abra-sive material as possible.b. Swab each sleeve wall, valve portand chamber with clean SAE 10 MotorOil at least twice.c. Wipe the oil out of the sleeveswith clean rags.d. Wash the sleeve bores and valvechambers with hot soapy water.e. Flush water jackets to remove for-eign material which might causeexcessive wear to the water pump.f. Remove the rags from the crank-shaft and wash the crankshaft offwith hot soapy water.g. Dry the cylinder block throughly.(Using compressed air)5. Reassemble the engine.134

Free to read online. Contents · Where is the serial number on a 9N, 2N or 8N?